
Your ES 350 idles with a faint shake at a stoplight on the way home to Blackhawk, and the shake smooths out once you pull away. Sometimes a steady check engine light shows up on the dash with it. A rough idle like that on this V6 usually means one cylinder is firing weaker than the other five. At Driven Auto Care of San Ramon, we start by finding which cylinder it is, because the injector, the spark plug and the ignition coil on that cylinder can each cause the same shake.
Finding the Cylinder That Misfires
The engine computer counts misfires on each of the six cylinders separately. We read those counts with a scan tool while the engine idles, and the cylinder with the climbing number is the one we work on. A stored code such as P0304 names the cylinder too, and the live count confirms the misfire is still happening.
Each of the six cylinders on this engine fires from a separate coil, and coils and plugs wear over the miles. So our first move is to trade the weak cylinder's coil with one from a cylinder that runs clean. If the misfire moves to the new spot, the coil is the part to replace. If the misfire keeps showing on the same cylinder after the coil and plug have both moved, the fuel injector on that cylinder is next in line.
How We Test One Injector Against the Others
An injector is an electric valve that sprays a measured shot of fuel for every firing of its cylinder. A weak one sprays too little, so the cylinder runs lean and stumbles. One with dirt in the tip can spray a stream in place of a fine mist, and that fuel never burns completely.
To check flow, we run a balance test. We put a gauge on the fuel rail, the tube that feeds all six injectors, and pulse each injector open for the same short time. Each pulse lets fuel out of the rail, and the gauge shows how far the pressure drops. Healthy injectors drop the pressure by nearly the same amount. The injector whose drop is clearly smaller or larger than the average of the others is the one that's flowing the wrong amount of fuel.
We also use the scan tool to shut off fuel to one cylinder at a time while the engine idles. Cutting a healthy cylinder makes the idle stumble hard. Cutting the weak one barely changes the idle, because that cylinder was doing little work to begin with. We check the injector's wiring and electrical resistance as well, since a broken wire gives the same symptom as a clogged tip.
Which ES 350 You Drive Changes the Test
ES 350 models from 2007 through 2018 use the 2GR-FE V6, which has six injectors that spray into the intake ports. The 2019 and newer ES 350 uses the 2GR-FKS V6, which has twelve: six port injectors and six direct injectors that spray straight into the cylinders under much higher pressure. On the newer car, we use the Lexus scan function that runs the engine on the port injectors alone and then on the direct injectors alone, while we watch the misfire counts. If the misfire shows up on only one of the two, we know which injector on that cylinder to test further.
The Rough Start After the Car Sits
We also look for an injector that leaks. An injector that fails to close tightly can drip fuel into its cylinder after you shut the engine off. The next start then runs rough for a few seconds, sometimes with a raw fuel smell, until the extra fuel burns off. When we pull the spark plug from that cylinder, it can come out wet with fuel. We confirm the leak by holding the fuel system at pressure with the engine off and watching how fast the pressure falls.
What the Repair Involves
On the 2GR-FE, we remove the upper intake to reach the fuel rail, and the injectors come out with the rail. Every injector we reinstall gets new seals and O-rings, and we put each one back in the cylinder it came from. Once the new parts are in, we clear the old codes from memory, read the misfire counts again at idle and on a drive, and confirm the fuel trims match on the two banks of three cylinders.
Call Driven Auto Care of San Ramon at (925) 830-4701 and describe the shake at idle or the rough start you've noticed. We'll find the cylinder that misfires and test its injector, then replace the part that failed. Your ES 350 then idles smooth again.








